This Robot use two motors control rear
wheels and the single front wheel is free. It has 4-infrared sensors on
the bottom for detect black tracking tape, when the sensors detected
black color, output of comparator, LM324 is low logic and the other the
output is high.
Microcontrollor AT89C2051 and H-Bridge
driver L293D were used to control direction and speed of motor.
Fig 1. Circuit diagram of my Robot.
Fig 2. Circuit
diagram of Infrared sensors and comparators.
AC to DC switching power adaptor circuit
with maximum output power of 90W. Switching power supply is built using
a high voltage power switching regulator IC MC33374 and some other
additional components. The MC33374 IC is a monolithic high voltage power
switching regulators that are specially designed to operate directly
from a rectified AC line source, and in flyback converter applications.
The MC33374 switching power adaptor
combines the required converter functions with a unique programmable
state controller. At various variable AC inputs, it is capable of
serving up to 6 A current at 15V output voltage. This switching power
adaptor is capable of providing an output power in excess of 150W with a
fixed AC input of 100V, 115V, or 230V, and in excess of 90 W with a
variable AC input that ranges from 85V to 265V.
This is a Phototransistor Detector circuit. In this circuit, when
the light falling on the phototransistor (Q1) is blocked, its
conductance will decrease and the voltage across Q1 will rise. When the
voltage rises above 1/2 of the supply voltage the output of the
comparator will turn ON and the LED will be lit.
The only critical part of this circuit is the value of resistor R1 which
in most cases can be 470K ohms but may have to be increase if the room
is dark or decreased if the room is well lit.
Increasing the value of R1 will cause the sensitivity of the sensor
to decrease. This may be necessary when the light falling on the cell
is not very strong or shadows can affect the phototransistor.
There are a number of phototransistors sizes and case styles.
The smaller cases will be easier to hide but connecting wires may be
more difficult.
Here is an ideal Mobile charger
using 1.5 volt pen cells to charge mobile phone while traveling. It can
replenish cell phone battery three or four times in places where AC
power is not available. Most of the Mobile phone batteries are rated at
3.6 V/500 mA. A single pen torch cell can provide 1.5 volts and 1.5
Amps current. So if four pen cells are connected serially, it will form
a battery pack with 6 volt and 1.5 Amps current. When power is applied
to the circuit through S1, transistor Q1 conducts and Green LED
lights.
When
Q1 conducts Q2 also conducts since its base becomes negative. Charging
current flows from the collector of Q1. To reduce the charging voltage
to 4.7 volts, Zener diode D2 is used. The output gives 20 mA current for
slow charging. If more current is required for fast charging, reduce
the value of R4 to 47 ohms so that 80 mA current will be available.
Output points are used to connect the charger with the mobile phone. Use
suitable pins for this and connect with correct polarity. The circuit
comes from here.
The Schematic
Mobile Phone Charger Circuit For Traveling
Today, in turn for the net, I have found a notice interesting. Polaroid, in co
llaboration with Zink Imaging has intention to release to short (the precise date still has not been specified) a new printing for photo super capacities them. The new “Digital Mobile Instant Photo Printer” will be equipped of Bluetooth logo's, in order to allow to print photo from the cellular one and Pocket PC without having to connect some cable, and Pict Bridge USB, compatible with the majority of blots some photographic in commerce. One of the characteristics that they hit more is technology ZINK (Zero Ink Printing Technology) used for the press process. This technology in fact I use not to preview it of cartridges, but the photos come printed publication on a special paper through the stimulation of the present polymers on this last one. The declared dimensions are 120x72x23 millimeter with a weight of 230 grams approximately (Enclosed batteries).
The appointment today with the Guides and Trucchi for
Windows Phone 7 is dedicated to the Bluetooth, and in particular to like
associating a cap, an earpiece, an external keyboard or any Bluetooth accessory
to I telephone Windows Phone 7. First of all we must ignite the Bluetooth.
* From the shielded Start we slide to sinistra per visualizing the
directory of the Applications.
*We slide the list and we touch on the Impostazioni.
* We touch the Bluetooth voice and we change the State on Ignited
* In this Windows moment it is already trying the present Bluetooth devices
near I telephone. We make sure therefore that our accessory already is ignited.
* Al term of the search we will see a directory with the several names of the
found accessories. We touch therefore what we want to install.
* To this point it could be demanded a PIN in order to associate the two
devices. Inserted therefore the present code in the handbook of the accessory
or a new one and touched on
Remote sensor sends
data via mains supply, Temperature range: 00.0 to 99.9 °C
This circuit is intended for precision centigrade
temperature measurement, with a transmitter section converting to
frequency the sensor's output voltage, which is proportional to the
measured temperature. The output frequency bursts are conveyed into the
mains supply cables. The receiver section counts the bursts coming
from mains supply and shows the counting on three 7-segment LED
displays. The least significant digit displays tenths of degree and
then a 00.0 to 99.9 °C range is obtained. Transmitter-receiver distance
can reach hundred meters, provided both units are connected to the
mains supply within the control of the same light-meter.
Transmitter circuit
operation:
IC1 is a
precision centigrade temperature sensor with a linear output of 10mV/°C
driving IC2, a voltage-frequency converter. At its output pin (3), an
input of 10mV is converted to 100Hz frequency pulses. Thus, for
example, a temperature of 20°C is converted by IC1 to 200mV and then by
IC2 to 2KHz. Q1 is the driver of the power output transistor Q2,
coupled to the mains supply by L1 and C7, C8.
The frequency pulses coming from mains supply and
safely insulated by C1, C2 & L1 are amplified by Q1; diodes D1
and D2 limiting peaks at its input. Pulses are filtered by C5, squared
by IC1B, divided by 10 in IC2B and sent for the final count to the
clock input of IC5. IC4 is the time-base generator: it provides reset
pulses for IC1B and IC5 and enables latches and gate-time of IC5 at 1Hz
frequency. It is driven by a 5Hz square wave obtained from 50Hz mains
frequency picked-up from T1 secondary, squared by IC1C and divided by
10 in IC2A. IC5 drives the displays' cathodes via Q2, Q3 & Q4
at a multiplexing rate frequency fixed by C7. It drives also the 3
displays' paralleled anodes via the BCD-to-7 segment decoder IC6.
Summing up, input pulses from mains supply at, say, 2KHz frequency, are
divided by 10 and displayed as 20.0°C.
D6 is the Most Significant Digit and D8 is the Least Significant
Digit.
R16 is connected to the Dot anode of D7 to illuminate permanently
the decimal point.
Set the ferrite cores of both inductors for maximum output (best
measured with an oscilloscope, but not critical).
Set trimmer R4 in the transmitter to obtain a frequency of 5KHz at
pin 3 of IC2 with an input of 0.5Vcc at pin 7 (a digital frequency
meter is required).
More simple setup: place a thermometer close to IC1 sensor, then
set R4 to obtain the same reading of the thermometer in the receiver's
display.
Keep the sensor (IC1) well away from heating sources (e.g. Mains
Transformer T1).
Linearity is very good.
Warning! Both circuits are connected to 230Vac mains, then some
parts in the circuit boards are subjected to lethal potential! Avoid
touching the circuits when plugged and enclose them in plastic boxes.
Here is an ideal Mobile charger
using 1.5 volt pen cells to charge mobile phone while traveling. It can
replenish cell phone battery three or four times in places where AC
power is not available. Most of the Mobile phone batteries are rated at
3.6 V/500 mA. A single pen torch cell can provide 1.5 volts and 1.5
Amps current. So if four pen cells are connected serially, it will form
a battery pack with 6 volt and 1.5 Amps current. When power is applied
to the circuit through S1, transistor Q1 conducts and Green LED
lights.
When
Q1 conducts Q2 also conducts since its base becomes negative. Charging
current flows from the collector of Q1. To reduce the charging voltage
to 4.7 volts, Zener diode D2 is used. The output gives 20 mA current for
slow charging. If more current is required for fast charging, reduce
the value of R4 to 47 ohms so that 80 mA current will be available.
Output points are used to connect the charger with the mobile phone. Use
suitable pins for this and connect with correct polarity. The circuit
comes from here.
The Schematic
Mobile Phone Charger Circuit For Traveling
To write SMS while guide is it self most dangerous. In some Countries he is also illegal and in passed they have been also of the serious incidents much for distractions of this type. The keyboards touchscreen, much fashionable ones in the smartphone more recent, than certainly of it do not facilitate the writing. Therefore Motorola it has created the earpiece bluetooth Command One.
Thanks to an application available for Android 2,2 and to the MotoSpeak technology, the customer can dictate the SMS to write and to send it without to watch the screen, simply dictating the commandos you premail. From the point of view hardware the earpiece is large 54 x 18,5 x 11 milimeter and hung 12 grams. The battery allows to an autonomy of 5 hours in conversation or 7 days in standby. In 15 minuteren, moreover, the battery is recharged of 50%. The device available for Will have been born them. Price not communicated.
The purpose of this simple circuit is to deter potential car burglars
by flashing a few LEDs on a seemingly very sophisticated control
panel,implying that the vehicle is equipped with a sophisticated hi-tech
alarm system. This simple deterrent is unique in the sense that it is
based on just one single uni junction (UJT) and is connected to the car
power supply system by just two wires.
The circuit
partly relies on it self and partly on the psychological fact that on
seeing a brightly lit and active control panel ( even when the car is
off ) similar to an alarm system, many thieves, especially the more
experienced ones, would don't like to.... to dare to attempt stealing
the car at the risk of setting off the alarm.
The
circuit as shown in schematic, is based on a UJT type 2N2646, which is
wired as a low frequency oscillator. The frequency is determined by the
timing components R1 and C1. Two LEDs are used in flashing mode and two
in normal forward conduction pilot mode.R2 and R3 limit the currents
passing through the LEDs .