Tuesday, March 8, 2011

Simple Switch On Time Delay Circuit

This Switch On Time Delay circuit has been designed to create a lamp switch operated electronically with an option of setting a delay in the time of execution of operation to reduce one or more lamps in a stairwell or any other places where this circuit may be useful. The circuit can be useful to control various lamp or appliances that can be connected in relay contacts.

The circuit that takes advantage of the emitter/base breakdown voltage of an ordinary bi-polar transistor. The reverse connected emitter/base junction of a 2N3904 transistor is used as an 8 volt zener diode which creates a higher turn-on voltage for the Darlington connected transistor pair. Most any bi-polar transistor may be used, but the zener voltage will vary from about 6 to 9 volts depending on the particular transistor used. Time delay is roughly 7 seconds using a 47K resistor and 100uF capacitor and can be reduced by reducing the R or C values. Longer delays can be obtained with a larger capacitor, the timing resistor probably shouldn't be increased past 47K. This Switch On Time Delay circuit should work with most any 12 volt DC relay that has a coil resistance of 75 ohms or more. The 10K resistor connected across the supply provides a discharge path for the capacitor when power is turned off and is not needed if the power supply already has a bleeder resistor.
Read more >>

Tuesday, February 22, 2011

ReWalk robotic exoskeleton

ike the REX robotic exoskeleton, ReWalk is a wearable, motorized robotic device that is worn outside the clothing. The motorized legs, which are held in place by leg braces and a harness worn around the waist and shoulders, are powered by a rechargeable battery providing 3.5 hours of use located in a backpack along with a computer. However, unlike the REX exoskeleton which is controlled by a joystick, the ReWalk uses motion sensors to detect the wearer’s movements and translate them into movement of the units’ motorized joints, similar to the eLEGS exoskeletondeveloped at UC Berkeley.

Unlike the robotic exoskeletons being developed mainly for military use, such as Lockheed Martin’s HULC and Raytheon’s XOS robotic exoskeletons, which are designed to amplify the wearer’s movements giving them increased strength, speed and endurance, ReWalk is controlled by detecting the subtle movements in the user’s center of gravity and upper-body movements.
For this reason the user needs crutches to assist with their balance when using ReWalk, which means it is only suitable for those with movement in their hands and shoulders. Unfortunately this means Goffer, who is a quadriplegic, isn’t able to use his creation. However, Argo Medical Technologies – the company he founded to commercialize the device – is working on a version suitable for quadriplegics.
The ReWalk weighs 15 kg (33 lbs.) and is designed to serve as a physical training device for those undergoing rehabilitation. By maintaining users upright on a daily basis it also helps alleviate many of the health-related problems associated with long-tern wheelchair use such as urinary, respiratory, cardiovascular and digestive problems.
The ReWalk has been undergoing clinical trials in Israel and the U.S. for several years and Argo Medical Technologies now plans to start selling the device to rehabilitation centers around the world from January 2011 for a cost of around US$100,000.
Read more >>

Monday, February 21, 2011

HyperSolar concentrator could boost solar cell output by 400 percent

Solar cells are the most expensive part of a solar panel, so it would follow that if panels could produce the same amount of electricity with less cells, then their prices would come down. In order for panels to be able to do so using existing cell technology, however, they would need to get more light to the fewer cells that they still had. Mounting the panels on the end of vertical poles to get them closer to the sun is one possible approach, that might work in the town of Bedrock or on Gilligan’s Island. A better idea, though, is to apply a clear layer of solar concentrators to the surface of a panel – and that’s just what HyperSolar intends to do.

The California company claims that it has just completed the prototype design of “the world’s first thin and flat solar concentrator for direct placement on top of existing solar cells.” Each sheet will contain a matrix of optical concentrators that are capable of collecting sunlight from a variety of angles. Beneath those concentrators will be a “photonics network,” that will channel light from all the collection points on the top to concentrated output points on the bottom. This network will also able to separate the sunlight into different spectrum ranges, so that specific ranges can be sent to specific cells designed to absorb them.
The sheets will also incorporate a photonics thermal management system, that will keep unusable parts of the solar spectrum from reaching the cells. This should keep the cells from overheating, and becoming less efficient.
While HyperSolar predicts that its product will be able to magnify the sun’s rays by 300 to 400 percent, not all cells will necessarily be able to handle that kind of intensity. For that reason, the solar concentrators will come in Low Magnification, High Magnification, and Mix-Mode Magnification models. At the 400 percent level, the company states that a concentrator-equipped panel could use 75 percent less cells than one without.
HyperSolar’s next step will be to produce an actual physical prototype, and see if it works as envisioned. We’ll keep you posted ...
From
Read more >>

Saturday, February 19, 2011

Thought-controlled car demonstrated

Since its formation in 2006, Freie Universität Berlin’s AutoNOMOS team has been researching and developing systems that could someday result in driverless, autonomous cars. Previously, they have successfully used an iPhone, an iPad, and an eye-tracking device to maneuver their Volkswagen Passat MadeInGermany test car. Now, using a commercially-available Emotiv EPOC brain-machine gaming interface, they have demonstrated that their car can be controlled by mind power.

AutoNOMOS’ system, known as BrainDriver, acquires bioelectric signals from the driver via 16 EEG sensors on the EPOC neuroheadset. Before slipping behind the wheel, drivers first need to spend some time on the system’s software tool kit, where they learn to move a cube back and forth on a computer screen by altering their thought patterns. Once on the road, BrainDriver links these patterns with assigned actuations (such as steering and acceleration), and sends the appropriate commands to the car’s drive-by-wire system.

In the first test of the technology, the car drove itself autonomously to an intersection, at which point its human occupant used their thought patterns to tell it which way to turn. In the second test, carried out at Berlin’s former Tempelhof Airport, the occupant continuously controlled steering, acceleration and braking. There was said to be “only a slight delay” between their mental commands and the subsequent reactions of the car.
The system is currently only a demonstration project. Team members, however, believe that it could have definite applications in the future, such as for allowing passengers to assist autonomous cars when the vehicles are unsure of which road to take at an intersection.
Read more >>

Tuesday, January 4, 2011

12V to 24V DC- DC Converter

This simple circuit is a DC-DC converter that converting up 12V source to a 24V. It can be used to run radios, small lights, relays, horns and other 24V accessories from a 12V vehicle with a maximum draw of about 800mA.
 The Schematic 12V to 24V DC- DC Converter

This DC-DC Converter can be used to charge one 12V battery from another, or step up the voltage just enough to provide necessary overhead for a 12V linear regulator. Using one op-amp as a square wave oscillator to ring an inductor and another op-amp in a feedback loop, it won't drift around under varying loads, providing a stable 24V source for many applications. With a wide adjustment in output this circuit has many uses.

Parts List
R1-R4,R7-R8 100K 1/4W Resistor
R5 470 Ohm 1/2W Resistor
R6 10K Linear Pot
C1 0.01uF Mylar Capacitor
C2 0.1uF Ceramic Disc Capacitor
C3 470uF 63V Electrolytic Capacitor
D1 1N4004 Rectifier Diode
D2 BY229-400 Fast Recovery Diode See Notes
Q1 BC337 NPN Power Transistor
U1 LM358 Dual Op Amp IC
L1 See Notes
MISC Board, Wire, Socket For U1, Case, Knob For R6, Heat sink for Q1

DC- DC Converter Notes
1. R6 sets the output voltage. This can be calculated by Vout = 12 x (R8/(R8+R7)) x (R6B/R6A).
2. L1 is made by winding 60 turns of 0.63MM magnet wire on a toroidal core measuring 15MM (OD) by 8MM (ID) by 6MM (H).
3. D2 can be any fast recovery diode rated at greater then 100V at 5A. It is very important that the diode be fast recovery and not a standard rectifier.
4. Q1 will need a heat sink.
Read more >>

Friday, December 31, 2010

Variable DC Power Supply With LM317

This DC power supply circuit is adjustable using IC Voltage Regulator LM317. LM317 is a versatile and highly efficient 1.2-37V voltage regulator that can provide up to 1.5A of current with a large heat sink. It's ideal for just about any application. This was my first workbench power supply and I still use it.

Since LM317 is protected against short-circuit, no fuse is necessary. Thanks to automatic thermal shutdown, it will turn off if heating excessively. All in all, a very powerful (and affordable!) package, indeed.

Although voltage regulator LM317 is capable of delivering up to 37V, the DC power supply output circuit here is limited to 25V for the sake of safety and simplicity. Any higher output voltage would require additional components and a larger heat sink.

Make sure that the input voltage is at least a couple of Volts higher than the desired output. It's OK to use a trim-pot if you're building a fixed-voltage supply.

Problems:
Follow all the safety precautions when working with mains voltage. Insulate all connections on the transformer.
Read more >>

Tuesday, December 28, 2010

6A, 5 Volt Power Supply

The standard variable voltage regulator type LM150 is fairly easily available, but at times its out, which is limited to about 3 amperes, may prove to e a limiting factor to its utility, nut the simple modification describe here allows the to be enhanced to about 6 amperes. The circuit has inbuilt safe area protection and thermal overload protection.The circuit has been tested for lone regulation of the order of about 0.01% volt and load regulation of about 0.1% volt.
The circuit works on principle similar to the compact 10A power supplies. The two LM150 regulators are wired in parallel mode with  IC3 which controls them. The output voltage is given by the relation
Vout=1,25x(1+R5/R4) volts. The input voltage may lie anywhere in the range of 12 to 30 volts.

The IC must be adequately heat sinked in order to obtain full output current all over the operative temperature range 

The circuit 6A, 5 volt Power Supply
Read more >>

32W HiFi Amplifier circuit based on TDA2050

This is a High Fidelify (Hi-Fi) amplifier circuit based on single IC TDA205. This is a mono channel audio amplifier. You need to build the same circuit for stereo channel.


TDA2050 Description:
The TDA 2050 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB audio amplifier. Thanks to its high power capability the TDA2050 is able to provide up to 35W true rms power into 4 ohm load @ THD =10%, VS = ±18V, f = 1KHz and up to 32W into 8ohm load @ THD = 10%, VS = ±22V, f = 1KHz. Moreover, the TDA 2050 delivers typically 50W music power into 4 ohm load over 1 sec at VS=22.5V, f = 1KHz.
The high power and very low harmonic and crossover distortion (THD = 0.05% typ, @ VS = ±22V, PO = 0.1 to 15W, RL=8ohm, f = 100Hz to 15KHz) make the device most suitable for both HiFi and high class TV sets.
Read more >>

Monday, December 27, 2010

High Current Regulated Supply

The high current regulator below uses an additional winding or a separate transformer to supply power for the LM317 regulator so that the pass transistors can operate closer to saturation and improve efficiency. For good efficiency the voltage at the collectors of the two parallel 2N3055 pass transistors should be close to the output voltage. The LM317 requires a couple extra volts on the input side, plus the emitter/base drop of the 3055s, plus whatever is lost across the (0.1 ohm) equalizing resistors (1volt at 10 amps), so a separate transformer and rectifier/filter circuit is used that is a few volts higher than the output voltage. The LM317 will provide over 1 amp of current to drive the bases of the pass transistors and assumings a gain of 10 the combination should deliver 15 amps or more. The LM317 always operates with a voltage difference of 1.2 between the output terminal and adjustment terminal and requires a minimum load of 10mA, so a 75 ohm resistor was chosen which will draw (1.2/75 = 16mA). This same current flows through the emitter resistor of the 2N3904 which produces about a 1 volt drop across the 62 ohm resistor and 1.7 volts at the base. The output voltage is set with the voltage divider (1K/560) so that 1.7 volts is applied to the 3904 base when the output is 5 volts. For 13 volt operation, the 1K resistor could be adjusted to around 3.6K. The regulator has no output short circuit protection so the output probably should be fused.
Read more >>

TDA7295, 80W Audio Amplifier

Below is a 80W amplifier circuit is constructed by using a power IC TDA7295. With a very simple design, makes this circuit very easy to build. TDA7295 has many features to support your audio system, the most important is that the IC has very low distortion and very low noise feature.


The TDA7295 is a monolithic integrated circuit in Multiwatt15 package, intended for use as audio class AB amplifier in Hi-Fi field applications such as home theatre and topclass TV. The wide voltage range and to the high out current capability make the TDA7295 able to supply the highest power into both 4W and 8W loads even in presence of poor supply regulation, with high Supply Voltage Rejection.
The built in muting function with turn on delay simplifies the remote operation avoiding switching on-off noises.
Read more >>